Handlebar Risers with Offset for BMW R 1200 RS, LC (2015-)

All Bikes

Handlebar risers with offset: 30mm higher and 21mm closer to the rider

Raising the handlebar by 30mm results in a more upright, much more relaxed seating position. Moreover, the handlebar is brought 21mm closer to the rider which additionally improves driving comfort. The overall result is a noticeable increase in stamina and concentration. Long stretches on the motorway are less nerve-racking.
Fits on original 32mm handlebar.
With EU street homologation!
Also referred to as handlebar risers, handlebar height increase, bar back risers, barbacks.

BMW R1200RS LC

Install Instruction

When mounting the handlebar risers, you have to reposition the clutch cable (see install instruction).
If repositioning the clutch cable is too complex, you can also extend it with our special adapter (part no. 26865), which is sold separately.
Install Instruction Extension Adapter for Clutch Cable
Example video installation instruction for the extension adapter for the clutch cable

If the original brake line is too short or tensioned after mounting the handlebar risers, the brake line can be extended with our special adapter (item no. 26860), which is sold separately.
Install Instruction Extension Adapter for brake line

Questions about this article

I have a BMW sat-nav support installed on the handlebars. Can this support be reinstalled in the same position after the risers are fitted?
Yes, the sat nav can be installed on the handlebar risers.
You can see this in the install instruction:
www.motorcycleparts-hornig.com/downloads/pdf/Montageanleitung_26207.pdf

---

Why can I not pull the clutch line as it is shown in the video / in the installation instruction?
The clutch line is fixed at the frame (behind the cooler) with a clamp (hose holder). You cannot see this clamp, you can only feel it when you grab along the clutch line with your hand. The holder must be opened and only then you can pull the clutch line (as shown in the video / installation instruction).

---

Do I need the additional screws (item 2534-520)?
BMW uses special screws with threads in their extended screw heads on the triple clamp in order to mount the navigation system there. If somebody does not want to mount the navigation system there anylonger, our shorter screws (2534-520) can be used. With these screws you do not have any disturbing screw heads with thread on the triple clamp. An elegant solution if you do not want to mount the support of the BMW GPS system on the triple clamp anylonger. Our short screws (2534-520) are not necessary for mounting the handlebar risers.

---

Ratings

Rating:
The average rating of this product is 5 of 5:
(after 6 Ratings)

---

Ray B. wrote | 2020-11-10:
Excellent quality handlebar risers and in my opinion the nicest to look at. They were very easy to fit. I re-routed the clutch cable following the instructional video kindly provided by Hornig on this website. There is no need to alter the brake cable. The risers have definitely made the bike more comfortable to ride for me. Highly recommended.

---

Dave B. wrote | 2019-03-20:
Excellent product,does the job nicely.Very good service from Hornig as usual.A1+++

---

Andy-y wrote | 2018-11-02:
Just the right amount of back and up so much more comfortable easy to follow instructions good quality item

---

steve wrote | 2018-07-24:
Perfect item. Just the right amount of extra height and rear movement of bars

---

BeO wrote | 2018-07-08:
They fit very well and make my ride so much better. They also make it easier to adjust my gps which i have shifted place to above the speedometer

---

Derijard wrote | 2018-06-23:
Perfect

---

Show all Make a new evaluation

Related / Recommended Products

Side stand plate

Feel safer when parking your bike on dirt or asphalt with a...

Price € 7,50
without VAT plus shipping

Show details

Oil filler plug with emblem

There is a drilling in the side of the plug in which you can...

Price € 29,00
without VAT plus shipping

Show details

Frame Covers - Engine Mounting rear

These covers for the open holes of the rear engine mounting...

Price € 32,90
without VAT plus shipping

Show details